800m FM Transmitter 9v battery

This is one of the smallest and neatest FM transmitters to be presented as a construction project and it has the advantage of being available as a complete kit of parts. This will save going to a number of suppliers as no single supplier has all the necessary components.
The circuit has been specially designed to demonstrate the techniques of FM transmission and to start you in the world of surface-mount assembly.
FM transmission is the best mode for transmitting a signal as it does not suffer from interference such as electrical noise from car engines or electrical appliances etc. It also achieves the greatest range with the least power.
With just a handful of components and a few milliwatts of output power you can produce an FM transmitter with a very impressive range and perfect clarity.

SUMMARY OF SPECIFICATIONS

Supply: 9 volts
Current consumption: 7mA
Battery life: 50 hours ZnC    100 hours alkaline
Tuning range: 80 - 110MHz (by stretching or compression the oscillator coil)
Fine tune by adjusting the air trimmer (2MHz adjustment)
Stability - Low. Bug to be left in-place and not to be moved or handled.
Antenna length - 175cm (5ft 9in)

 With a 175cm (5ft 9in) (half-wave antenna) supplied in the kit, the range has been conservatively rated as 800 metres (2400ft) under normal working conditions. In many countries you must reduce the maximum range to 30ft (10metres) by cutting the antenna to 10 inches. If this is the case, you must abide by it. Some countries totally ban these brilliant devices. You need to find out the situation in your own locality.
To introduce surface-mount technology to our range of projects, we have started with resistors. These are the easiest of the surface-mount components to identify and fit.
Some of the other components such as capacitors and transistors are so small they are almost impossible to solder by hand and surface-mount capacitors are not marked in any way so they become easily mixed up if you are not very careful.
Surface-mount technology is entirely different to normal through-hole placement and some of the differences are explained in this article.
The major difference is size and if you are having trouble soldering 1/4 watt resistors, you will have ten times more difficulty with surface mount. SM items are so small it takes the keenest eyesight to read the figures on the component and the nimblest of fingers to pick them up and place them.
But until you buy a kit and see what the parts look like, you will have no idea if you will be able to cope.
Nevertheless surface mount has arrived and is here to stay. Most modern designs already include surface mount components and many are already entirely surface mount. Take pocket cameras, watches, pendant transmitters, toys, video recorders, video cameras and computers for example. Their miniaturisation has been almost entirely due to using smaller componentry.
Surface mount is very easy to implement on a large scale as the components are available in large quantities on reels or in tubes but when it comes to a one-off project, things are different. Few suppliers sell individual surface-mount components and some sell them in lots of 10 or 100. The normal purchase for surface-mount is on a reel of 1,000 to 5,000 pieces.
The only solution is to provide a kit and to make it easy for everyone to put together, we have just converted the resistors to surface-mount.
Some of the other components are not available in surface-mount (such as the coil) and there is no real advantage in converting everything to surface mount as the battery cannot be reduced in size without reducing the number of hours of operation.
The main difficulty with surface mount is placing them on the printed circuit board and holding them in place while soldering. There are a number of aids to help you do this, such as solder pastes and solder creams, silicon and infra-red setting glues but most of these come in syringes and cost as much as $20 for a 1oz (30gm) tube. For a simple project, this additional cost is out of the question.
To keep costs down we are going to hand solder each resistor without the aid of glue and the technique we use is called RE-FLOW SOLDERING.
Re-flow soldering only requires two hands. Normal soldering requires three hands - one to hold the component in place, one to hold the soldering iron and one to hold the solder. If you have three hands available, (such as the help of an assistant), you can use the normal soldering method.
Basically re-flow soldering consists of heating up the solder on the board AND THE END OF THE RESISTOR AT THE SAME TIME so that the resistor makes a perfect connection to the board. This is discussed fully in the soldering section.

HOW THE CIRCUIT WORKS
The circuit consists of two stages - an audio amplifier and an RF oscillator.
The electret microphone contains a FET transistor and can be counted as a stage, if you wish. The microphone detects audio in the form of air vibrations that enter the hole (at the end of the mic) and move the diaphragm. This diaphragm is a thin piece of metallised plastic such as mylar and is charged with electrical charges during manufacture.
Next to this is a metal plate containing a number of holes so that the air readily passes through. The relative distance of the mylar diaphragm to the metal plate makes the charges move on the diaphragm (remember static electricity theory: like-charges repel and unlike-charges attract). Some of the charges pass down a lead that touches the metal plate and into a FET amplifier - it looks like a three legged transistor. The FET amplifies the charges and gives a reading on the output lead.
The output must be connected to a supply via a resistor called the load resistor. The FET draws a varying current during its operation and this creates a varying voltage on the output (across the load resistor).
The reason why a FET has been used is due to it having a very high input impedance and does not have any loading effect on the charges.
The output waveform from the microphone will be typically 3 - 30mV in our case, depending on how close it is to the source of the sound. The circuit is capable of detecting a whisper at 10ft (3M) and only very sensitive microphones have been included in the kits.
You can also get medium and low sensitivity devices from suppliers so you have to be careful as they are not labelled.
A 22n capacitor on the output of the microphone couples the signal to the input of the first audio amplifier stage. This capacitor is designed to separate the DC voltage on the microphone from the base voltage on the transistor.
The first transistor stage consists of transistor and two biasing resistors.
The stage is said to be "AC coupled" as it has a capacitor on both the input and output so the DC voltages of the other stages do not influence the voltage on the stage.
The stage is also said to be "self-biased" with the 1M base resistor turning the transistor on until the collector voltage drops to about half rail voltage. The value of the base resistor is chosen so that this occurs.
The value can be chosen by experimentation. If the value is too low, the voltage on the collector will be below half rail. If it is too high, the collector voltage will be too high. The AC gain of the stage is about 70 and the signal is amplified and passed to the oscillator stage via a 100n capacitor.
The signal is now typically 200mV to 2,000mV in amplitude and this is adequate for injection into the oscillator stage.
The oscillator stage is designed to operate at about 100MHz and this frequency is set by the value of inductance of the 5 turn coil and the capacitor(s) across it. The 39p and air trimmer can be considered as a single capacitor. The frequency is also determined to a lesser extent by the transistor, the 10p feedback capacitor and also the 470R emitter biasing resistor and the 47k base bias resistor. The supply voltage also has an effect as the oscillator can be classified as voltage controlled.
There are a lot of things that set the frequency and even though the parts have a 5%, 10% or even 20% tolerance, they are STABLE at their present value. The 10p and 39p are NPO types and this means they are stable even when the temperature changes a small amount. The frequency is firstly set by pushing the turns of the coil closer together to lower the frequency or pulling them apart to raise the frequency and then the air trimmer is adjusted to obtain the precise frequency required. The air trimmer has a range of about 2MHz.
The circuit will stay at the desired frequency providing the supply voltage remains constant and the temperature of the parts do not rise appreciably (such as when the project is left in the sun etc).
Voyager MkII is not designed to be handled and is not suitable to be worn on the body. It is designed to be placed on a shelf and left in position.
The most important components in the oscillator stage are the coil and capacitor(s), making up the parallel tuned circuit. 
They do almost all the work in setting the frequency and generating the waveform. The transistor merely turns on at the correct instant in each cycle to deliver a small amount of energy to the tuned circuit. 
How this is done: The transistor is firstly turned on via base-bias resistor and it injects a small amount of energy into the parallel tuned circuit.  A few low-amplitude cycles now take place and we pick up the operation when the tuned circuit is operating at full amplitude and producing a sinewave at about 100MHz. This frequency is called the CARRIER.
The parallel tuned circuit is also called a TANK CIRCUIT and the name was coined during the development of the earliest transmitters where it was found a coil and capacitor in parallel would smooth out electrical pulses like filling a water tank in bursts so that it delivers an even flow of water.
This name has stayed with us and is an ideal way of describing a coil/capacitor combination.
The waveform from the tank circuit is passed to the 10p and this modifies the voltage on the emitter of the transistor.
There are two ways of turning on a transistor. One is to raise the voltage on the base while holding the emitter fixed and the other is to hold the base rigid while lowering the voltage on the emitter.
The second method is used in this circuit and the 10p moves the emitter up a very small amount at the rate of 100 million times per second to turn the transistor off.
The base is held rigid via a 1n capacitor and this value is sufficient to hold the base rigid at 100MHz but allows it to move up and down at audio frequencies so that audio being processed by the first transistor can be passed to the oscillator.
The oscillator transistor does not determine the waveshape of the signal, it mainly delivers a pulse of energy to the tank circuit at the correct instant where the coil and capacitor do all the work in creating the carrier signal. There is one more feature of the tank circuit. Even though it is injected with a pulse of energy of only a few millivolts, it is capable of producing a higher amplitude waveform on its output. In other words the tank circuit is capable of amplifying the voltage supplied to it. This is called its Q-factor.
The other two components in the stage are the 47k base-bias resistor and 470R emitter resistor. The 47k turns the transistor on when the power is first applied and sets the operating point for the stage. The 470R emitter resistor acts as a current limiting resistor and allows the transistor to be injected via the emitter.
The voltage produced by the tank circuit is monitored by the 10p and passed to the emitter of the transistor. During a portion of the cycle, the voltage it delivers, turns the transistor off. This effectively removes the transistor from the circuit and allows the waveform from the tank circuit to be passed to the antenna.
When a waveform at 100MHz is passed into a wire (such as an antenna) the signal is very easily radiated as electromagnetic energy. This is how the signal is radiated to the surroundings.
The 22n supply capacitor across the battery is designed to tighten up the power rails. The power rails have also been kept tight by connecting the battery directly to the printed circuit board.
Note: The circuit will not operate from a power supply without generating a lot of "mains hum" - the annoying 100 or 120 cycle hum from the mains - you must use a battery to get a crystal clear, hum-free, output.
Test voltages have been provided on the circuit diagram to help with servicing. They are only approximate and apply to our prototype. They show how each transistor has a voltage on the base of about 0.6v, with respect to the emitter, to turn it on.
The voltages around the oscillator stage cannot be measured with an ordinary multimeter when the circuit is operating as the leads of the multimeter will act as an antenna and kill the operation of the circuit. This is certainly the case on the emitter of the second transistor, where the leads of a multimeter will draw off so much energy that the stage will stop working.
Because you cannot detect the operation with a multimeter, we have developed a piece of test equipment called a LED POWER METER. This is covered below and shows how the output of the high frequency RF oscillator stage can be measured without loading it too much.
 

FM Transmitter with double transistor

The next progressive step is to add a transistor to give the electret microphone more sensitivity. The electret microphone contains a Field Effect Transistor and you can consider it to be a stage of amplification. That's why the electret microphone has a very good output.
A further stage of amplification will give the bug extremely good sensitivity and you will be able to pick up the sound of a pin dropping on a wooden floor.
Many of the 1 transistor circuits over-drive the microphone and this will create a noise like bacon-and-eggs frying. The microphone's used by Talking Electronics require a load resistor of 47k for a 6v supply and 22k for a 3v supply. The voltage across the microphone is about 300mV to 600mV. It will produce an audio waveform of about 2-20mV.
Only a very simple self-biasing common-emitter stage is needed for the audio amplifier. This will give a gain of approx 70 for a 3v supply. The next circuit shows this audio amplifier, added to the previous transmitter circuit. This circuit is the best design using 2 transistors on a 3v supply. The circuit takes about 7mA and produces a range of about 200 - 400metres.

2 Transistor FM Transmitter

Five points to note in the circuit above:
1. The tank circuit has a fixed 39p and is adjusted by a 2-10p trimmer. The coil is stretched to get the desired position on the band and the trimmer fine tunes the location.
2. The microphone coupling is a 22n ceramic. This value is sufficient as its capacitive reactance at 3-4kHz is about 4k and the input to the audio stage is fairly high, as noted by the 1M on the base.
3. The 1u between the audio stage and oscillator is needed as the base has a lower impedance as noted by the 47k base-bias resistor.
4. The 22n across the power rails is needed to keep the rails "tight." Its impedance at 100MHz is much less than one ohm and it improves the performance of the oscillator enormously. 
5. The coil in the tank circuit is 5 turns of enameled wire with air core. This is much better than a coil made on a PC board and is cheaper than a bought inductor. The secret to long range is high activity in the oscillator stage. The tank circuit (made up of the coil and capacitors across it) will produce a voltage higher than the supply voltage due to the effect known as "collapsing magnetic field"  and this occurs when the coil collapses and passes its reverse voltage to the capacitor. The antenna is also connected to this point and it receives this high waveform and passes the energy to the atmosphere as electromagnetic radiation.
When the circuit is tightly constructed on a PC board, the frequency will not drift very much if the antenna is touched. This is due to the circuit design and layout as well as the use of large-value capacitors in the oscillator. If low value capacitors are used, the effect of your body has a greater effect on changing the frequency. 

Fm Transmitter PNP Design

Before we go to an improved design, here is an unusual circuit using a PNP (BC 557) transistor. Firstly, PNP transistors do not work as well as NPN transistors. I would reverse the 4k7 and electret mic as the voltage between base and 0v rail is very small and the 4k7 is not biasing the transistor - it is not needed! The range will be 50 to 100 metres and the current is about 3mA.
Note: A reader built this circuit. It did not work!!
Try putting the 47p across the coil. The 33p may need to be reduced to 10p.
It is just a BAD design, but a good challenge to see if you can get this type of design to work.
 

Simple 1 transistor FM Transmitter

The 22n is not shown. This is a later addition.

FM Transmitter Bad Layout

Here is a circuit with a very bad layout. The circuit may work but it relies on a "Q-factor" from the coil and capacitor in the tank circuit to produce a high voltage. This high voltage gives the circuit a good range.
Firstly the coil and capacitor should be near each other. The coil should not have long leads. and a 22n capacitor should be across the supply to give the circuit better performance. The value of C2 is too high. It should be 10p. The coil should be 5 turns. The electret mic should not be connected directly to the base of the transistor. As you can see, the circuit is full of faults.
You can learn a lot from other people's mistakes.   

Simplest FM Transmitter

The following circuit is the simplest FM circuit you can get. It has no microphone but the coil is so MICROPHONIC that it will pick up noises in the room via vibrations on a table.
The circuit does not have any section that determines the frequency. In the next circuit and all those that follow, the section that determines the frequency of operation is called the TUNED CIRCUIT or TANK CIRCUIT and consists of a coil and capacitor. The transistor and components surrounding the tuned circuit simply keep the tuned circuit operating at its RESONANT FREQUENCY. This circuit does not have this feature. The transistor turns on via the 47k and this puts a pulse through the 15 turn winding. The magnetic flux from this winding passes through the 6 turn winding and into the base of the transistor via the 22n capacitor. This pulse is amplified by the transistor and the circuit is kept active.
The frequency is determined by the 6 turn coil. By moving the turns together, the frequency will decrease.  The circuit transmits at 90MHz. It has a very poor range and consumes 16mA.

 THE SIMPLEST BUG

  The components soldered to the 2 cells

Rear view of the simplest bug